Homelogologo
Homelogologo
ReleasesBurro Website
PlatformsBurro VerdeMaintenanceMaintenance Procedure

Maintenance Procedure

Tire Care and Maintenance

Regularly check tire pressure to ensure optimal performance and localization.
Lug Nut Torque: 80 ft-lbs (108.5 Nm)

Available Tire Options

  • Standard (18×8.5×10, Code R3, 22 PSI, 4 PLY): general-purpose tire with deep treads.

  • Traction (20×8.5×10, Code R1, 24 PSI, 4 PLY): for soft, uneven terrains (grass, soil, sand).

  • Non-Marking (18×8.5×8, Code R3, 22 PSI, 6 PLY): for concrete and paved surfaces without leaving marks.

Updating the Tire Profile in Software1

Tap the Settings icon2

From the main menu, tap the Settings icon.

Tap Manage Profiles and Add-ons3

Open the Manage Profiles and Add-ons menu.

Select the Add-ons tab4

Switch to the Add-ons tab.

Tap Tire Selection5

Open the Tire Selection screen.

Choose the matching tire profile6

Select the profile that matches the newly installed tires.

Relaunch the software7

Tap Relaunch to apply the change.

Changing a Tire

note:

Tools Needed

  • Jack and jack stands (rated > 1200 lbs)

  • Wheel chocks

  • Torque wrench

  • 21 mm socket

Park on a level surface1

Park the Burro on a hard, level surface.

Perform full shutdown and disconnect batteries2

Complete the shutdown procedure and disconnect both batteries.

Chock the opposite wheels3

Place wheel chocks on the wheels opposite the tire being changed.

Position the jack4

Set the jack under the designated jack point near the wheel.

Raise the Burro5

Lift until the tire clears the ground.

Secure with a jack stand6

Place a jack stand under the frame near the jack.

Remove lug nuts7

Use the 21 mm socket to remove and set aside the lug nuts.

Remove the old wheel8

Pull the wheel off the hub.

Mount the new wheel9

Place the new wheel on the hub and hand-tighten lug nuts.

Lower until tire touches ground10

Slowly lower the Burro until the tire just contacts the ground.

Torque the lug nuts11

Use the torque wrench to tighten lug nuts to 80 ft-lbs in a star pattern.

Lower completely and remove supports12

Lower the Burro fully, then remove the jack and jack stand.

Lifting and Hoisting

When lifting the machine, follow these safety procedures:

  • Use only designated hoist points on the frame (front and rear, between wheels).

  • Always support the Burro on jack stands; never rely on the jack alone.

Function Test after Maintenance

Elevate the Burro1

Raise the Burro so all wheels spin freely.

Power on and wait2

Turn on the machine and wait for the UI to load.

Test manual controls3

From a safe position, press Forward and Reverse on the yellow control panels to confirm correct wheel rotation.

Test Person Follow mode4

Activate Person Follow; verify wheel direction and beeps when you approach.

Lower and return to service5

Lower the Burro to the ground and resume operation.

Cleaning

warning:

Pressure warning

  • Do not use a high-pressure washer.

  • Do not direct compressed air within 6 inches of electronics enclosures or sensors.

General Cleaning

  • Use compressed air or a low-pressure hose for most components.

Sensors & Screen

  • Clean cameras, LiDAR sensor, and touchscreen with lens wipes or a soft, damp cloth.

Enclosures

  • Ensure USB and charging ports are sealed before washing.

Top Tray

  • Remove and clean separately.

Wheel & Motor Area

  • Use a low-pressure hose to wash dirt and mud from wheels and chassis.

Adjustments

Tap the Settings icon on the touchscreen UI to access adjustments.

General Settings

  • Speed: overall maximum speed.

  • Row Speed / Row Distance: for RowNav mode.

  • Stop Time: pause duration at stations.

  • Lights: toggle main LEDs (safety flashes remain active).

  • Language: UI display language.

  • Manage PIN: set a 4-digit PIN to lock settings.

  • Manage Profiles and Add-ons: configure tire and attachment profiles.

Accessing Additional Menus

Tap “General” in Settings1

On the Settings screen, tap “General” at top left.

Choose from the side menu2

Select one of:

  • Advanced (acceleration, eco mode, obstacle handling)

  • GPS (localization modes, base-station pairing)

  • Launch + Record (diagnostic data)

  • Developer (experimental settings)

Localization and GPS Setup

To Check GPS Status

  • Quick View: tap Localization Status icon on main menu.

  • Advanced View: Settings > General > GPS.

In the GPS menu, select Manage Navigation Mode, choose GPS (Base Station), and tap Apply Changes.

Select GPS Base Station2

Return to GPS menu, tap Select GPS Base, enter the 4-digit serial number, and tap Save.

Other Modes

  • GPS (NTRIP): default RTK corrections over cellular.

  • GPS (Off) / Vision: indoor use via cameras.

  • LiDAR: full indoor navigation, including towing.

Indoor Navigation with Reflective Paint

  • Operate within 2–3 m of painted lines for LiDAR detection.

  • Keep lines clean and unobstructed.

Advanced Settings

  • Acceleration/Deceleration: route start/stop rates.

  • Eco Mode: battery conservation when stationary.

  • Audio: toggle audible alerts.

  • Obstacle Detection:
    • Min. Obstacle Height: ignore objects below set height.
    • Robot/Trailer Width: adjust for towing (max 9 ft).
    • Obstacle Avoidance (Experimental).

  • Demo Mode: manual control and person follow only.

Switching User Interfaces

Open Manage Profiles and Add-ons1

Settings > Manage Profiles and Add-ons.

Select Main Screen tab2

Choose the Main Screen tab.

Choose and confirm new UI3

Select BOSS or BOSS Pro and confirm to restart.